60W / 120W amplifiers :
-1 – off XLR microphone input with Phantom power supply desk microphones MBT 1101 series ( RJ45 , CAT5 SFTP cable )
– 1 – off MIC / LINE inputs with Phantom , MIC or LINE selector
– 2 – off XLR balanced microphone inputs with Phantom power supply ( MIC1 with A.P.T. adjustment )
-2 – off AUX inputs for sound sources ( TAPE / CD )
– Micro – switches for setting priorities and input functions
– Up to 8 desk microphone with cascade connection
– TEL / EMERG input for emergency calls with input level and activation threshold ( A.P.T. ) adjustment
-Line auxiliary output
– Loudspeakers line outputs ( constant voltage 50-70-100V / low Impedance 8 Ohm )
– Terminal strip for 24Vdc external power supply
– Terminal strip for precedence connection
– Warning signal ( chime ) level adjustment
-FBT AMPLIFIERS MPA5480-MPA5240-MXA1120-MDS SERIES

transformer attenuators circuit TL10-RE:

These attenuators enable the sound level in a room to be adjusted by attenuating the sound performance of the speaker units with a transformer in constant-voltage systems (100, 70, 50 V). Each attenuator has an autotransformer, an 11-position switch (10 positions + Off) and front masks. They are available with different output powers, depending on the load that can be connected to them.

Each model (TL10-RE, TL30-RE and TL60-RE) has a by-pass relay able to exclude the attenuator in case of an alarm and/or emergency signal having priority (activation of the relay with a 24 VDC current on an additional two-pole line). They can be easily flush-mounted on a wall using the AC911 box or secured to a wall using the AC913 adaptor.

transformer attenuators circuit TL10-RE 10W Attenuator

The TL10-RE attenuator is equipped with a by-pass relay capable of excluding attenuation in the presence
of alarm and/or emergency signals having priority. It can be easily flush-mounted using the Paso AC911
box or wall-mounted using the AC913 adapte

Cooper Menvier FL-RL-R-D Conventional Xenon Sounder Beacon (Deep Base)
The Xenon is an audible and visual device which requires one single installation point. This greatly reduces installation costs and is less obtrusive than two separate devices. Versions are available with the sounder and beacon linked, or with separate terminals for independent operation

The Honeywell FSL100 Series Flame Detectors are Optoelectronic flame detectors for a wide range of Light Industrial fire detection from Honeywell Analytics.

Honeywell’s FSL100 range of Light Industrial/Commercial Flame Detectors enables simple coverage of fire hazard areas across many fire hazard applications. Installation, set-up and operation are simple. Wide solid area coverage and fast speed of response optimise safety. With inbuilt automatic test and test lamps available to cover all models, reliability is ensured.

A range of middle-market Optical Flame Detectors join the HA FSX High-End products. Addresses a wide range of fire protection applications both indoors and outdoors. With 3 versions to cover a wide range of flaming fires: Ultraviolet (UV), Ultraviolet/Infrared (UV/IR) and Triple Infrared (IR3).

Detecting a wide range of Hydrocarbon and Non-Hydrocarbon flaming fires means that many application areas can be addressed. Wide viewing angleOptical detection of radiant energy in a solid angle Field of View enables coverage of a large risk area. A simple optional mounting bracket allows the FSL100 to be installed and aligned covering the hazard. Fast responseFar faster than other technologies, by responding to flaming fires in seconds enabling a more rapid response to danger before the fire can escalate.

FM Class 1, 2 & 3 Div2 can be installed indoors or outdoors and in Hazardous areas typically looking into a Div 1 area from a distance. FM 3260 performance certified to FM 3260 for flame Detector performance. Relay and current output (Fault and Alarm) Analog stepped output and Alarm/Fault relays for simple connectivity. Inbuilt Automatic Test and Simple to use Test LampsFSL100 maintains continuous internal health monitoring. Test lamps enable simple operational and field-of-view testing.

The FX 6100/FX61002 range is available as a high specification 1 or 2 loop intelligent addressable control panel, offering sophisticated functionality with simple end user operation.
FX6100 uses soft addressing to minimise installation time and remove the potential for error associated with manual addressing.
Features and Benefits
.Available in 1 and 2 loop versions
.Up to 200 addresses per loop
.Full network capability up to 126 panels
.Soft addressing
.Large versatile touch-screen user interface
.Multi-language selection capability
. Integral battery and power supply
.Flexible cause and effect programming
.Simple to operate end user touch-screen interface​

Cooper FX2204CFCPD Conventional 4 Zone Control Panel
The FX2200 ranges of conventional control panels provide a solution to any conventional system requirement. The advanced features include a simple “one-shot” user test facility, class change contacts, battery voltage alarms and charger temperature compensation, all included as standard to ensure ease of use and high reliability.

The FX6000PR is a cost effective passive repeater panel
which can be programmed via its informative display to
be either fully passive (display only) or semi passive
(restricted system control).
When loop connected the repeater panel will display the
system information text of the connected control panel
and will provide a fire indication, with panel number,
of any connected network control panel that has fire
activation.

Eaton FXN501 Addressable Surface Callpoint is compatible with the Eaton: JSB range of intelligent addressable fire systems. These intelligent addressable call points are attractively designed, simple to install, and are supplied as standard with a frangible glass element and a test key for ease of maintenance

Gent S4-34740 Beam Sensor Pair (Transmitter and Receiver) Excluding Bracket and Base

Gent S4-34740 S-Quad Addressable Loop Powered Beam Sensor Pair provides an enhanced solution for linear beam detection for applications where Gent S4 Vigilon point detection is either not practical or economic.

Powered and controlled via the loop, the beam is a market leading device with features such as one man alignment and commissioning which is achieved using the auto gain setting, this ensure the optimum alignment is reached.

Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire.

The Gent loop powered beam is certified to EN54 parts 12 and 17. Compatible with the full range of Vigilon and Nano control panels the S-Quad beam uses the panel software to ensure a fast response to fire while offering software filters to reduce the number of unwanted alarms.

The COMPACT-NC is a Compact Network Card for Vigilon Compact Control Panels.
This copper network card is used to allow data to pass between control panels in a Vigilon Compact networked fire system. The card must be plugged into the Master Control board MCB of the panel in a dedicated slot ‘CARD 2’. The card has terminals to accept external network wiring. A bank of dual-in-line switches on the card allow setting of address number and baud rate.
Key Features
* Links together 2 or more Vigilon Compact or Vigilon Compact Plus fire alarm panels.
* Expands the Vigilon compact panel

Gent COMPACT-PLUS Vigilon Compact Plus 1-2 Loop Control Panel with 1 Loop Card
Vigilon Plus Control Panels are available in 3 sizes managing 2, 4 or 6 loops each accommodating up to 200 devices including advanced fire sensors, interfaces, call points, alarm sounders and visual alarms. The Compact Plus 2 loop panels and Vigilon Plus 4 loop panels are available with integrated 24 hour standby and the 6-loop panel has full 72 hr standby capacity

The S4-710 is specifically designed to be used with the Gent Vigilon range of Analogue Addressable Control Panels. This detector is an Optical Type Analogue Addressable Smoke Detector combined with a Heat Detection Element. It requires a Gent S4-700 base for mounting.
The S4-710 is a truly intelligent analogue sensor combining local processing in the sensor and the panel to achieve an immediate response to real fires whilst minimising the risk of false alarms.

Gent S3-S-R S3 Sounder with Red Body
* S-Cubed offers a comprehensive range of loop powered alarm sounders with integrated voice and EN54-23 certified visual alarms. Combined with flexible configuration from the Gent by Honeywell fire control panels, this loop powered device can give a differentiated combination of audible and visual alarms for alert and general evacuation.

The Gent S-Cubed offers a comprehensive range of loop powered alarm sounders with integrated voice and visual alarms. The sounders shall be capable of providing 3 different sound signals, which are selected/configured via the main control panel. Configuration of sounder patterns will not be carried out locally at individual sounders. In order to meet with the requirements of BS5839 Part 1, the frequency of sound signals emitted will be as follows:
Features & Benefits:
* 200 per loop
* Red & White options
* 103dbA at 1 metre
* 3 Sound signals
* 2 integral Line Isolators