2-way system
White or black ABS enclosure
5″ LF woofer
0,75″ HF tweeter
100V Line transformer (15/25/40/50W)
Directional wall mount bracket included
Connection via plug in «euroblock» connector
The FBT 550WHT/BT two way speaker unit is equipped with a 100V line transformer and provides the possibility of an 8
Ohm connection. An exclusive fully adjustable support bracket provide a flexible mounting system for virtually any
application. The low frequency section is a 5″ woofer and the high frequency section is a 0,75″ tweeter. The power
selector switch is installed in the rear of the enclosure. The loudspeaker system meets the following performance
criteria: line transformer with power taps for 15/25/40/50W, frequency response from 80Hz to 20kHz (-10dB)

40w 2 WAY BASS REFLEX SPEAKER UNIT
PROJECT 640 6.5 woofer and 1 tweeter passive installation speakers feature a fully adjustable support bracket for easy installation. Connection is via a Euroblock connector. 8 Ohm and 100V – Recommended Amplifier: 80W RMS. Long Term Power:

PROJECT passive installation speakers feature a fully adjustable support bracket for easy installation. Feature a 3.5 woofer and 0.5 tweeter. Connection is via a Euroblock connector

transformer attenuators circuit TL10-RE:

These attenuators enable the sound level in a room to be adjusted by attenuating the sound performance of the speaker units with a transformer in constant-voltage systems (100, 70, 50 V). Each attenuator has an autotransformer, an 11-position switch (10 positions + Off) and front masks. They are available with different output powers, depending on the load that can be connected to them.

Each model (TL10-RE, TL30-RE and TL60-RE) has a by-pass relay able to exclude the attenuator in case of an alarm and/or emergency signal having priority (activation of the relay with a 24 VDC current on an additional two-pole line). They can be easily flush-mounted on a wall using the AC911 box or secured to a wall using the AC913 adaptor.

transformer attenuators circuit TL10-RE 10W Attenuator

The TL10-RE attenuator is equipped with a by-pass relay capable of excluding attenuation in the presence
of alarm and/or emergency signals having priority. It can be easily flush-mounted using the Paso AC911
box or wall-mounted using the AC913 adapte

bosch 240 W power amplifier

in a 2U high housing
EN 54‑16 certified
70 V / 100 V and 8 ohm outputs
Dual inputs with priority switching
100 V input

for slave operation on 100 V speaker
line

The PLN-24CH12 Battery charger, 24V makes sure that
the system batteries are always charged in public
address and emergency sound systems. Rackmountable,
the unit charges lead‑acid batteries and
simultaneously provides 24 V for system components.
The battery charger is fully compliant and certified to
EN 54‑4. The battery charger is a microprocessor
controlled device of premium quality.

shure mvl clip-on microphone:

the headphone jack of a smartphone or tablet and opening recording apps
such as the ShurePlus® MOTIV recording app, the user can easily and discretely capture high-quality audio. It is ideal for use in speech and other applications requiring minimal visibility.

Shure mvl clip-on microphone features:

• Superior audio clarity
• Effective immunity to audible interference
• Low self-noise
• More even, natural response across frequency range
• Less susceptible to distortion
• Matte black, sleek, low-profile design for inconspicuous placement
• Snug-fit foam windscreen provides additional protection from plosives and wind noise
• Includes protective storage pouch, tie clip, and windscreen
• The optional Rycote Mini Windjammer fits over the included windscreen
• Legendary Shure quality and reliability

shure slx wireless systems:

Wireless system offers easy set-up and high audio quality for virtually any application. Features include Automatic Frequency Selection, Automatic Transmitter Set-Up, Predictive Diversity technology, and removable antennas with rack hardware.

Frequency Band Selection

Most countries closely regulate the radio frequencies used in the transmission of wireless Infor mation. These regulations state which devices can use which frequencies, and help to limit the amount of RF (radio frequency) interference in all wireless communications. To be flexible enough to operate worldwide, SLX receivers are available in a number of models, each with a unique frequency range. Each frequency range, or band, spans up to 24 MHz of the

wireless broadcast spectrum.

To facilitate system setup and protect against RF interference, each system comes with multiple predefined frequency groups and channels.

When using a single SLX system, the operating frequency will generally not have to be changed. In an installation with multiple receiver/transmitter systems, each system must operate on a sepa rate channel. The group and channel system provides an optimum frequency spread when using multiple systems.

Within a single frequency band, up to 12 individual transmitter/receiver systems may be used in a single installation. In regions where additional frequency bands are available, it is possible to operate up to 20 systems simultaneously. Check with your local Shure retailer for information on which bands are available in your area

shure slx wireless systems instructions:

Single System Setup
Follow these steps when using a single SLX system : Automatic Frequency Selection Scans for an available channel and sets the receiver to that channel . Automatic Transmitter Setup
1. Turn On the transmitter.
2. Open the transmitter battery compartment to display the infrared ( IR ) port
3. With the IR port exposed to the receiver , press sync .
4. Hold the sync button until the red light stops flashing on both receiver and transmitter .
5. When the receiver ready light glows , the system is ready for use .
6. Close the transmitter battery compartment .

A-1712 ER

Description

Type: Mixer amplifier with 120 watts of power.

Zones: 2 zones.

Inputs: 9 channels (6 microphone inputs + 3 auxiliary audio sources).

Zone Selection: Capability to select and manage different zones.

Recording Output: Option to add an output for connecting to a recording unit.

Additional Audio Source: Ability to add extra audio sources.

A-2030 H 4

Description

Amplifier Power: 30 watts.

Inputs: 5 channels (3 microphone inputs + 2 auxiliary audio sources).

Additional Features: Capability to add an extra audio source.

A-2120DD-EB
Digital Mixer Amplifiers

The A-2120DD-EB is a high cost-performance mixer power amplifier suited for broadcasting paging or background music in schools, offices, shops, factories, mosques, churches and large rooms.

3 microphone inputs, 2 AUX input and 1 recording output
DD-varieties with 2 phone jacks and 1 5-pin DIN input
D-varieties with 3 phone jacks
Speaker output of constant voltage distribution system (100 V)
Independent tone control of boost and cut type for both high and low frequency
MIC 1 with phantom power and mute function
Current limiter to prevent damage due to current overload
Excess heat limit to protect the transistor and power transformer

The A-2240 is a high performance mixer power amplifier
suited for broadcasting paging or background music in
schools, offices, shops, factories, mosques, churches
and large rooms.

BS-1015BSW

Description
Type: Headset with a streamlined design and white color.

Operation at 100V: 15 watts, 10 watts, or 5 watts.

Operation at 70V: 7.5 watts, 5 watts, or 2.5 watts.

The BS-1030 is a small, 2-way bass-reflex type
speaker featuring a wide frequency range suitable
for use for announcements and music playback. The
BS-1030B can be used for both high-impedance and
low-impedance applications. The speaker’s splashproof construction permits it to be installed under the
eaves where the speaker is not directly exposed to rain.

BS-633A

Description

Speaker Type: 6-watt speakers with a streamlined design, ideal for mounting on concrete ceilings or walls.

Installation: Suitable for both ceilings and walls.

Operation at 100V: 6 watts, 3 watts, or 1 watt.

Operation at 70V: 3 watts, 1.5 watts, or 0.5 watts.